Radar and sensor technologies for defence and security

Sentirox is an electronics company working in sensing technologies, with FMCW radar and RF sensors at its core. Its main field is defence and security; the company also works on the use of the same sensor technologies in sectors such as aviation, industrial automation and automotive. Every project is carried through from user requirements to field verification under a single engineering process.

Business areas

Business areas

Work is organised in two application areas and two technology areas. Each area is described on its own page.

  • A small UAV hovering overhead, seen from the ground

    Ground‑to‑air sensing

    Detection, tracking and classification of low-altitude targets and small UAVs with ground-based FMCW radar and RF sensors. The principal applications are the protection of sites, units and convoys.

  • Aerial view of mountainous terrain

    Air‑to‑ground sensing

    Sensors that look down from air platforms: FMCW radar altimeters, approach and landing support, terrain and obstacle sensing, proximity sensors and ground target detection. Small size and low power consumption are the first requirements in this area.

  • Close-up of a surface of pyramid-shaped absorber foam

    Radar and RF sensors

    Short-range FMCW radar sensors whose chirp waveform, antenna and RF front end, signal processing and calibration are designed together. The common technology base of both application areas.

  • A signal generator and an oscilloscope on a laboratory bench

    Sensor electronics and embedded software

    Small, low-power sensor boards designed for series production and the real-time embedded software that runs on them; data interfaces, built-in test and production test.

Company profile

  • Based inAnkara, Türkiye
  • Field of activityDesign of FMCW radar and RF sensors, sensor electronics and embedded software
  • Main sectorDefence and security
  • Other sectorsAviation, industrial automation, automotive, robotics
  • Business areasGround‑to‑air and air‑to‑ground sensing; radar and RF sensors; sensor electronics and embedded software

Sentirox organises its work in two groups: the application areas, and the technology base they share.

The applications group comprises ground‑to‑air and air‑to‑ground sensing; the technologies group comprises FMCW (frequency-modulated continuous-wave) radar and RF sensors, and sensor electronics and embedded software. On every project, the company follows an engineering process that begins with a precise definition of user requirements and continues through design, measurement and verification.

The sensors are designed primarily for defence and security applications. Proximity, distance, level, speed and motion sensing are also needed in industrial automation, automotive, robotics, logistics, agriculture, energy, and smart city and building systems, and the company’s field of activity covers these sectors as well.

About us

Project stages

A sensor project runs through three main stages, from requirement definition to use in the field. Each stage is closed out against predefined acceptance criteria.

  1. Design

    User requirements are flowed down to sensor and sub-unit level; waveform, antenna, board architecture and component selection are decided at this stage. Board and software design advance through preliminary and critical design reviews (PDR, CDR).

  2. Measurement and verification

    Prototypes are measured on the bench and in the field with reference targets. Laboratory measurement, simulation and field recordings demonstrate that the sensor meets its requirements.

  3. Qualification, production and life cycle

    Environmental and electromagnetic compatibility tests are planned to the standards that apply to the environment in which the sensor will be used. Every produced unit is delivered after a defined acceptance test (ATP). Calibration, spares, software updates and training needs are addressed from the design stage onwards.

Domestic and national technology

In line with Türkiye’s objective of reducing its defence industry’s dependence on imports, Sentirox aims to contribute to the domestic design and production of critical sensors.

To that end, the company’s approach is to develop design knowledge and software source code in-house, to work with domestic suppliers and to retain engineering expertise within its teams.

In component selection, the aim is to prefer parts that are not subject to foreign export restrictions (ITAR and similar) and to assess compliance with the export-control legislation of Türkiye and of supplier countries from the start of design.

Careers

Sentirox welcomes applications from engineers who want to work in RF and radar, embedded software, electronics, mechanical, systems and test engineering.

The application process is the same for recent graduates and experienced engineers: candidates apply by email, enclosing a CV.

Careers

Contact

Sentirox can be reached by email for corporate matters, collaboration enquiries and job applications.